Low Profile & High Protection with the Low-Vis Plate Carrier Elite (LVPC-E) by Chase Tactical The Low-Vis Plate Carrier Elite (LVPC-E) was designed with direct feedback from our customers asking for features of our original LVPC with features from our very popular SOCC plate carrier.  The LVPC-E is a low-profile, slick plate carrier built for Low Visibility and concealment. It is fully adjustable on the shoulders for size, and the sides are made from double layer Mil-Spec elastic. The Low-Vis Plate Carrier Elite (LVPC-E) also incorporates 3 internal pouches on each side which can hold rifle magazines, tourniquets, and/or radios. The sides of our Low-Visibility Plate Carrier are fully adjustable for girth by way of Velcro closure.  The interior of the LVPC-E has moisture wicking spacer mesh adding additional comfort to the body when worn.  The front of the LVPC-E incorporates a large Velcro area for placards and 2 vertical clips which will accept a variety of pre-configured weapon-specific pouch panels. Chase Tactical Low-Visibility Plate Carrier Elite (LVPC-E) Key Features: Removable cummerbund with Double Layer Mil-Spec Elastic 3 Internal Pouches on each side of Cummerbund Fully adjustable shoulder straps Large Velcro area for placards Vertical Clips for rapid add/removal of auxiliary chest worn equipment Front/Rear interior moisture wicking spacer mesh Made with Mil-Spec IR Treated 500D Cordura All our Fabrics are treated at source to deliver the lowest I.R. Signature possible. Sizing: REGULAR: Fits 10″ x 12″ Plate (Standard Size) X-LARGE: Fits 11″ x 14″ Plate (Most Uncommon Size)

The SK7 Kourass plate carrier is a next generation light weight and low profile carrier. Not only it offers unsurpassed load support and comfort it is also designed to be virtually unbreakable. SK7’s Kourass is the only vest carrier available with our SAFEgo quick release system. Based on magnetic light weight buckles SAFEgo let the operator to release the carrier with a simple finger movement at the same time that it guarantee a proper fit and operational safety. Using laser cut MOLLE systems offers a light weight alternative to traditional webbing with the same load capacity. All the materials integrated in SK7’s Kourass are proudly made in the United States. Features: Constructed with U.S. made original Cordura®. 500 Denier and 1,000 Denier available. Minimum 10 rows of laser cut MOLLE to attach any available pouches, accessories and holsters. laser cut MOLLE rows on the back 5 laser cut MOLLE rows on each side plate pouches.  Detachable front MOLLIE with SAFEgo buckle and Velcro® hook and loop.  Heavy duty drag handle.  Can handle 10 1/4" x 13 1/4" front and back plates and 6x6” and 6x8” side plates.  Fully adjustable in girth and height for customizing your fit. Original Velcro® panel on the front and back allows you to attach patches for customized ID.

The ultimate protection, breathability, and comfort with the Lightweight Operational Plate Carrier (LOPC)  Designed by U.S. Veterans. The Chase Tactical Lightweight Operational Plate Carrier (LOPC) is a lightweight plate carrier that works with any set of hard armor plates and soft armor backers. The LOPC has built-in padded and fully adjustable shoulder straps. The tops of the shoulder straps have both nylon webbing and elastic webbing for mounting and routing tourniquets, hydration tubes, radio antennas, handsets, comm wires, V Lites, and strobe lights.  The front of the Chase Tactical Lightweight Operational Plate Carrier incorporates a large matching Velcro loop area for placards and 2 vertical clips which will accept a variety of preconfigured weapon-specific pouch panels.  The LOPC comes standard with a removable MOLLE clip placard held in place by 2 vertical clips. Spacer mesh is used on the inside of the LOPC for increased breathability and comfort. The cummerbund is made of lightweight breathable mesh with MOLLE webbing on the exterior and interior. Strong drag handle that Velcro’s down and out of the way when not in use. Key Features: Removable cummerbund with Mil-Spec Velcro Lightweight breathable cummerbund with MOLLE webbing on the exterior and interior. Vertical Clips for rapid add/removal of auxiliary chest worn equipment Comes standard with a removable MOLLE clip placard Interchangeable cummerbund system Fully adjustable & padded shoulder straps Spacer mesh for comfort & breathability Strong drag handle that Velcro’s down Large Velcro area for placards Made with Mil-Spec IR Treated 500D Cordura Mil-Spec IR Treated Murdock Webbing All our Fabrics, Webbing, and Plastic Hardware are treated at source to deliver the lowest I.R. Signature possible. Sizing: REGULAR: Fits 10″ x 12″ Plate (Standard Size) X-LARGE: Fits 11″ x 14″ Plate (Most Uncommon Size)

The Rescue Task Force Basic Heavy Duty Plate Carrier is a highly customizable plate carrier vest with many of the best features that you are looking for. The front and rear panel plate carrier compartments will accommodate the standard size and the newer larger armor plates up to 11" X 14" in size. The cummerbund also features side armor pockets to accommodate side armor plates up to 6” X 8”. The plate carrier has fully adjustable heavy duty nylon shoulder straps and large quick connect buckles to adjust how high or low the front and rear panels sit from the wearer’s shoulders. The cummerbund is adjustable in length from a medium to 2XL+ t-shirt sizes, up to a 51” chest/waist size. The front, rear, and side panels all feature MOLLE webbing for customization of your plate carrier to what your mission requires. Fully compatible with MOLLE accessories like holsters, magazine pouch, and utility pouches. The Rescue Task Force Basic Heavy Duty Plate Carrier is a very tough and well made plate carrier with reinforced double stitching in all the critical locations as well as sizing options to fit a wide variety of rescuers among various shifts. FEATURES: MOLLE webbing on the front, back, and side panels allow the attachments of MOLLE accessories like holsters, mag pouches, utility pouches, and other essential gear. Adjustable for length cummerbund with MOLLE webbing, cummerbund can be extended out to 51"L Side pockets will allow for 6" X 8"  side armor panels/plates. Hook and Loop fasteners on the ends of the cummerbund to secure with the front panel hook and loop fasteners, for a secure fit. Adjustable for length Shoulder straps with large heavy duty quick connect buckles and with hook and loop fasteners. Includes two padded shoulder covers with MOLLE webbing, hook and loop fasteners, and loops for communications cabling routing. Top three MOLLE webbing rows on the front and back panels have loop fasteners for attaching (hook) Unit, ID, and name tapes to the front and rear panels. Heavy Duty drag handle on the top of the rear panel. 10"X 6" front pocket with hook and loop enclosure. Breathable mesh inner panels with separate internal pockets for soft body armor panels and hard plate armor. Made with tough and durable PVC material that is water and chemical resistant. Double and re-enforcement cross stitching in critical areas.

The ultimate protection, breathability, and comfort with the Lightweight Operational Plate Carrier (LOPC)  Designed by U.S. Veterans. The Chase Tactical Lightweight Operational Plate Carrier (LOPC) is a lightweight plate carrier that works with any set of hard armor plates and soft armor backers. The LOPC has built-in padded and fully adjustable shoulder straps. The tops of the shoulder straps have both nylon webbing and elastic webbing for mounting and routing tourniquets, hydration tubes, radio antennas, handsets, comm wires, V Lites, and strobe lights.  The front of the Chase Tactical Lightweight Operational Plate Carrier incorporates a large matching Velcro loop area for placards and 2 vertical clips which will accept a variety of preconfigured weapon-specific pouch panels.  The LOPC comes standard with a removable MOLLE clip placard held in place by 2 vertical clips. Spacer mesh is used on the inside of the LOPC for increased breathability and comfort. The cummerbund is made of lightweight breathable mesh with MOLLE webbing on the exterior and interior. Strong drag handle that Velcro’s down and out of the way when not in use. Key Features: Removable cummerbund with Mil-Spec Velcro Lightweight breathable cummerbund with MOLLE webbing on the exterior and interior. Vertical Clips for rapid add/removal of auxiliary chest worn equipment Comes standard with a removable MOLLE clip placard Interchangeable cummerbund system Fully adjustable & padded shoulder straps Spacer mesh for comfort & breathability Strong drag handle that Velcro’s down Large Velcro area for placards Made with Mil-Spec IR Treated 500D Cordura Mil-Spec IR Treated Murdock Webbing All our Fabrics, Webbing, and Plastic Hardware are treated at source to deliver the lowest I.R. Signature possible. Sizing: REGULAR: Fits 10″ x 12″ Plate (Standard Size) X-LARGE: Fits 11″ x 14″ Plate (Most Uncommon Size)

The Tasmanian Tiger Lightweight Laser Cut Plate Carrier is an extremely high quality, comfortably system for everyday patrol or special operations use.  It is designed to integrate with a variety of backpacks, specially the Tasmanian Tiger Medic Packs.  The inside walls are lined with cool fabric with a channel along the middle for cooling and comfort. The plate pockets are designed for medium sized SAPI plates, approximately 10" x 12". Features: Shoulder straps can be adjusted in length Length-adjustable elastic side attachment Front panel detaches for loading Front and side areas with MOLLE system for individual extension Laser cut MOLLE system Integrated radio equipment pocket

The Chase Tactical Low-Vis Plate Carrier M1 (LVPC-M1) The LVPC-M1 is a combination of our Low-Vis Plate Carrier and our Triple 5.56 Velcro Mag Pouch.  The LVPC-M1 is a low profile slick plate carrier and fully adjustable on the shoulders for size. The sides are made from double layer Mil-Spec elastic and incorporates 2 internal pouches on each side which can hold mag pouches, tourniquets and/or radio. The sides are fully adjustable for girth by way of Velcro closure. Key Features: Removable cummerbund with Double Layer Mil-Spec Velcro Removable Triple Velcro 5.56 Mag Pouch 2 Internal Pouches on each side of Cummerbund Fully adjustable shoulder straps Large Velcro area for placards Made with Mil-Spec IR Treated 500D Cordura Mil-Spec IR Treated Murdock Webbing All our Fabrics, Webbing, and Plastic Hardware are treated at source to deliver the lowest I.R. Signature possible. Sizing: REGULAR: Fits 10″ x 12″ Plate (Standard Size) X-LARGE: Fits 11″ x 14″ Plate (Most Uncommon Size)

The Chase Tactical Quick Response Carrier (QRC) was developed as a minimalistic no thrills, no frills plate carrier that is lightweight, functional and robust. When worn with ballistic inserts, the QRC can be quickly donned for rapid action response to high threat scenarios such as Active Shooter, Entries, Home Defense, or other critical incidents. Key Features: Adjustable 2″ Wide Shoulder Straps Adjustable 2″ Waist Strap with Quick Release Buckles Front & Back 4″x8″ Color Matched Velcro Area for ID Placards Strong drag handle that Velcro’s down Bottom Load Armor with an Internal Stirrup to Adjust Height Front & Rear MOLLE Webbing Made with Mil-Spec IR Treated 500D Cordura Mil-Spec IR Treated Murdock Webbing All our Fabrics, Webbing, and Plastic Hardware are treated at source to deliver the lowest I.R. Signature possible. Sizing: REGULAR: Fits 10″ x 12″ Plate (Standard Size) X-LARGE: Fits 11″ x 14″ Plate (Most Uncommon Size)

The Chase Tactical Quick Response Carrier (QRC) was developed as a minimalistic no thrills, no frills plate carrier that is lightweight, functional and robust. When worn with ballistic inserts, the QRC can be quickly donned for rapid action response to high threat scenarios such as Active Shooter, Entries, Home Defense, or other critical incidents. Key Features: Adjustable 2″ Wide Shoulder Straps Adjustable 2″ Waist Strap with Quick Release Buckles Front & Back 4″x8″ Color Matched Velcro Area for ID Placards Strong drag handle that Velcro’s down Bottom Load Armor with an Internal Stirrup to Adjust Height Front & Rear MOLLE Webbing Made with Mil-Spec IR Treated 500D Cordura Mil-Spec IR Treated Murdock Webbing All our Fabrics, Webbing, and Plastic Hardware are treated at source to deliver the lowest I.R. Signature possible. Sizing: REGULAR: Fits 10″ x 12″ Plate (Standard Size) X-LARGE: Fits 11″ x 14″ Plate (Most Uncommon Size)

The LVPC is a low profile slick plate carrier and fully adjustable on the shoulders for size. The sides are made from double layer Mil-Spec elastic and incorporates 2 internal pouches on each side which can hold mag pouches and/or radio. The sides are fully adjustable for girth by way of Velcro closure. Key Features: Removable cummerbund with Double Layer Mil-Spec Velcro 2 Internal Pouches on each side of Cummerbund Fully adjustable shoulder straps Large Velcro area for placards Made with Mil-Spec IR Treated 500D Cordura Mil-Spec IR Treated Murdock Webbing All our Fabrics, Webbing, and Plastic Hardware are treated at source to deliver the lowest I.R. Signature possible. Sizing: REGULAR: Fits 10″ x 12″ Plate (Standard Size) X-LARGE: Fits 11″ x 14″ Plate (Most Uncommon Size)

The VISM Quick Release Heavy Duty Plate Carrier designed to fit larger front & back armor plates up to 11" X 14" in size. MOLLE webbing for the ultimate in custom configuration. The integrated QR strap setup will allow the VISM Quick Release Plate Carrier to separate into 4 separate panel pieces in case of an emergency that requires the quick removal of the plate carrier from the wearer. FEATURES: MOLLE webbing on the front, back, and side panels allows the attachments of MOLLE accessories like holsters, mag pouches, utility pouches, and other essential gear. Adjustable for length cummerbund with MOLLE webbing, cummerbund can be extended out to 51"L. Hook and Loop fasteners on the ends of the cummerbund to secure with the front panel hook and loop fasteners, for a secure fit. Adjustable for length Shoulder straps with large heavy duty quick connect buckles and with hook and loop fasteners. Includes two padded shoulder covers with MOLLE webbing, hook and loop fasteners, and loops for communications cabling routing. Top three MOLLE webbing rows on the front and back panels have loop fasteners for attaching (hook) Unit, ID, and name tapes to the front and rear panels. Heavy Duty drag handle on the top of the rear panel. 10"X 6" front pocket with hook and loop enclosure. Breathable mesh inner panels with separate internal pockets for soft body armor panels and hard plate armor. Made with tough and durable PVC material that is water and chemical resistant. Double and re-enforcement cross stitching in critical areas.